Skip to content
White Rose Door & Opener Co.Request a visit
Open 24/7(289) 802-4769Call now
Person holding metal bars beside exposed coiled springs above a garage door. — Torsion Spring Replacement, Aurora

Emergency Springs · Aurora

Torsion Spring Replacement

Nothing broke outright, but the door has grown heavier each winter, opens more slowly and squeals as it moves. The springs on an older door have lost tension and the coils show pitting, so the system is asking for attention before it fails.

Call now · open 24/7(289) 802-4769

Request a visit

Right now

Before the door is looked at

Call (289) 802-4769, open 24/7.

  1. When a spring breaks, the safe approach for the household is to leave the door where it is, keep people and vehicles clear, and avoid running the opener, which can damage the top section, the trolley or the gear drive.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

  3. Never drive a vehicle at a closed door to get out; the door collapses and the stored tension in the counterbalance is released. Use the release, the outside key release, or a technician.

In plain words

The finished result is a door that behaves the way a good garage door should: it lifts by hand with light effort, stays where you leave it at mid-height, closes softly and lets the opener run with little strain. Reaching that point involves measuring the door, choosing a matched spring, winding it to the correct turns and testing the balance through the full travel. The technician then runs the opener's reversal test and lubricates the moving parts. You are left with a record of the spring installed, so future service starts from known specifications.

Sound familiar?

Looking up at the coil above the door, you can see a clean split with a gap of several centimetres between the two halves. The rest of the spring looks fine, but the door has become almost impossible to move by hand.

How the visit goes

Torsion Spring Replacement · Aurora

How the visit goes

Technician holding a black decorative strap hinge on a beige paneled garage door and driving a screw with a yellow drill.
  1. 1

    Following the hardware the spring drives

    The spring is one part of a chain, so the check follows that chain from the shaft outward. The centre bearing and the end bearings are turned by hand to feel for roughness or wobble. Cable drums are inspected for cracked flanges and worn grooves, and lift cables are examined along their length and at the bottom brackets, where fraying and rust usually start. Bottom brackets and their fasteners are looked at for corrosion, and the shaft is checked for straightness. Findings here decide whether the visit is a spring swap alone or a spring plus a few tired companions.

  2. 2

    Reconnecting and testing the opener

    With the door balanced, the opener comes back into service. The trolley is re-engaged, power is restored and the door is run open and closed under motor. Travel limits are adjusted so the door seals at the floor and stops at the right height, and force settings are set to the light load a balanced door presents. The technician then places an object flat on the floor in the door's path and confirms the door reverses on contact, and passes a hand through the photo-eye beam to confirm the door reverses again. These checks close the visit on a working, safe system.

  3. 3

    Keeping the spring in good shape

    A little care keeps the new spring running smoothly for its full life. Once or twice a year, spray the coils with a garage-door lubricant so the steel moves without rubbing, and do the same for the hinges, roller bearings and the end bearings at each side of the shaft. Autumn is a good time, since cold thickens grease and stiffens hardware. Leave the track dry, because lubricant there collects grit. Over the years, glance at the spring for gaps or rust streaks, and if the door starts to feel heavier by hand, book a balance check before a spring reaches its limit.

In the van

  • Torsion springs, oil-tempered or galvanized
  • Winding bars
  • End bearing plates
  • Locking pliers for the track
  • Socket set and wrenches

What affects the quote

  1. 1

    Condition of the lift cables

    Cables that show fraying, rust or a kink at the bottom brackets are replaced so the new spring pulls on sound steel. Two good cables mean this item stays off the list.

  2. 2

    Spring specification

    The wire size, inside diameter and length that the door's weight and height demand determine which spring is fitted. Larger doors take larger springs, and unusual combinations may need specially wound coils.

  3. 3

    One spring or two

    A single-spring door needs one spring; a paired system is usually replaced as a matched set of left- and right-wound springs. The number of springs and whether both are replaced is the largest single influence on the scope.

Same fees day, night or weekend.

Have it ready

Before you call · 0 / 3

(289) 802-4769

Torsion Spring Replacement: questions

Advice · (289) 802-4769

What happens if the header wood or centre bracket is damaged?

The centre bracket anchors the spring's reaction force to the framing above the door, so it has to be solid. If the header has split or softened, or the lag bolts have pulled, the technician can refasten into sound wood, add a reinforcing plate or replace the bracket before the new spring is wound. Dealing with this first keeps the shaft level and the spring pulling straight, which protects the bearings and the door.

What is the difference between galvanized and oil-tempered springs?

Oil-tempered springs are the traditional dark grey or black coil; they hold their tension well over time and are widely used. Galvanized springs have a zinc coating that resists rust, which is useful in damp garages, though they tend to relax slightly and may need a small adjustment after settling in. Both are available in standard and high-cycle ratings, and the technician can explain which suits your garage.

Do I need to be home for the visit?

It helps to have someone present to open the garage, point out anything you noticed and hear how the door should feel afterwards. The technician needs power at the opener outlet, clear space under the shaft for a ladder, and access to both sides of the door. If a vehicle is inside, it stays until the door is working. Being there also lets you approve any extra items, such as bearings or cables, as they come up.

York, Ontario

Aurora information

Town
Aurora, York, Ontario
In business
21 years
Hours
Open 24/7 · nights, weekends and holidays, same fees
Visits
On-site assessment preferred. Request a visit or call.

What the census means at the door

22%

Newer homes. About 22% of homes in Aurora were built in 1980 or earlier, according to the 2021 Census.

Many newer homes have a keypad by the door, several remotes and an app that reports whether the door is open. We keep all of these talking to the opener, clear codes from devices that have gone missing and set up new ones so the whole household is covered.

60%

Mostly houses. Single-detached houses make up about 60% of homes in Aurora (2021 Census).

Single-detached homes give a technician room to work: a driveway for the van, side room beside the tracks and a clear header. That means spring replacement, opener installation and full door replacement can each be finished in one visit with the door properly secured throughout.

Source: Statistics Canada, 2021 Census of Population

Open Aurora in Google Maps

Open 24/7

Request a visit

Nothing broke outright, but the door has grown heavier each winter, opens more slowly and squeals as it moves.

Call now · open 24/7(289) 802-4769
  • On-site assessment preferred
  • Same fees day, night or weekend
  • 21 years in business